Page Comparison

...

Goal: To move the NMIS database off of the same partition as /usr/local , and at the same time , make a backup of the NMIS runtime.  To accomplish this goal we first need a location where we will move/copy the files to, for this example I will use a target of /opt/nmis8.  Once we have this we will copy all of NMIS8 to the new location, then edit the config files in the current location to use the new data directories.

1. Copy or move files to new directory (on a production system, you should stop NMIS from polling by editing the crontab and appending a "#" to the lines for NMIS polling).

   1. Copy files to a new directory

      Code Block
      cp -rrp /usr/local/nmis8/database /opt/nmis8

   2. Move files to a new directory

      Code Block
      mv /usr/local/nmis8/database /opt/nmis8

   3. If you have a large database and copying or moving files takes a significant amount of time then we will prefer to use rsync.  In this case do not stop NMIS from polling at this time, it will be done in a later step. We will do a "hot" copy now and follow it with a "cold" copy.

      Code Block
      #do a hot copy where nmis is still updating sudo rsync -av --inplace /usr/local/nmis8 /opt/

2. Fix Check permissions on the copied files.  If you missed the -p option you may need to run these commands: (Not needed if you used rsync as all permissions will be copied with the files)

   Code Block
   chown -Rv nmis:nmis /opt/nmis8 chmod -Rv g+w /opt/nmis8

3. If you have a large database, now is the time to stop NMIS from polling.  As mentioned previously, the safest way to do this is by commenting out the lines that run NMIS polling, be sure to do all of them, just to be safe. Another option (and not necessarily recommended) is to stop the cron daemon with: service crond stop #Do Not forget to restart it later.  Now we will run the rsync copy one more time to get any updates: 

    

   1. Stop polling.  Wait for nmis to stop updating. 

      Code Block
      crontab -e #comment out all nmis.pl lines # continue running the following command until you no longer see nmis running ps aux | grep nmis.pl # make sure you don't see a line like this: # /usr/bin/perl ./nmis.pl

   2. Now that NMIS is no longer polling we can run a "cold" copy to get the last updates that NMIS made while we were "hot" copying. 

      Code Block
      sudo rsync -av --inplace /usr/local/nmis8 /opt/

4. Edit config files so that NMIS will write data to our new location, edit /usr/local/nmis8/conf/Config.nmis 

   Code Block
   # this line line 13: '<nmis_data>' => '<nmis_base>', # should change to line 13: '<nmis_data>' => '/opt/nmis8',

5. To test, move the existing data directores to new folders. 

   Code Block
   mv /usr/local/nmis8/database /usr/local/nmis8/database_old

6. Run a manual update, you should see no errors. 

   Code Block
   /usr/local/nmis8/bin/nmis.pl type=update debug=1 # you should not see any errors like this: # createRRD, ERROR (localhost) unable to create /opt/nmis8/database/health/server/localhost-reach.rrd: creating '/opt/nmis8/database/health/server/localhost-reach.rrd': No such file or directory

7. Open or reload the NMIS web page and everything should still look the same.

8. After confirming there are no errors you can now safely delete the old database directory. 

   Code Block
   theme Emacs
   rm -rf /usr/local/nmis8/database_old

9. Now re-enable your cron jobs.  If you commented lines out, remove the comments.  If you stopped crond, start it again: service crond start

Conclusion

In addition to moving the database folder, it may also be a good idea to move the logs folder if you are running short of space on the partition holding /usr/local.

...