...
iptables -L
on your NMIS server, as well as /etc/selinux/config
and the exit code of selinuxenabled
.SNMPD, Net-SNMP and collecting stats of the NMIS server itself
NMIS8 ships with one default node configured for collection, primarily to prove it is all working. This node is called localhost
and NMIS will collect statistics from your NMIS server using SNMP - if an SNMP agent is available, or just Ping statistics if not.
However, the installer does not automatically configure this local Net-SNMP daemon; if you would like to collect the NMIS server's statistics follow the instructions below - otherwise you're done with the installation.
You will likely want to consult and use the example configuration for Net-SNMP's snmpd
, which ships with NMIS in the file <nmisdir>/install/snmpd.conf
.
Because the installer has installed Net-SNMP for you already, you only need to backup its default config and move in the NMIS example one. You should very much modify this config to secure the SNMP read access according to your organisation's security policy!
Code Block |
---|
cd /usr/local/nmis8 mv /etc/snmp/snmpd.conf /etc/snmp/snmpd.conf.orig mv /etc/snmp/snmptrapd.conf /etc/snmp/snmptrapd.conf.orig cp install/snmpd.conf /etc/snmp/snmpd.conf cp install/snmptrapd.conf /etc/snmp cp install/snmptrapd.options /etc/sysconfig/snmptrapd # for CentOS/Red Hat only |
Debian/Ubuntu
The last command in the list above will fail as there is no /etc/sysconfig directory on this platform. Instead the snmptrap service is started by the snmpd service, and is enabled by updating the file /etc/default/snmpd:
Code Block |
---|
TRAPDRUN=yes |
Auto Start SNMP Daemons
Ensure that you tell Linux to start SNMPD automatically
Code Block |
---|
/sbin/chkconfig snmpd on /sbin/chkconfig snmptrapd on |
Debian/Ubuntu
Code Block |
---|
sysv-rc-conf snmpd on service snmpd start |
Run a Test Update
Once your local snmpd
is running, you can run a test update operation:
Code Block |
---|
sudo /usr/local/nmis8/bin/nmis.pl type=update node=localhost info=true |
The output will look similar to this example:
Code Block |
---|
Copyright (C) Opmantek Limited (www.opmantek.com) This program comes with ABSOLUTELY NO WARRANTY; This is free software licensed under GNU GPL, and you are welcome to redistribute it under certain conditions; see www.opmantek.com or email contact@opmantek.com NMIS version 8.5.6G 14:42:47 runPing, INFO (localhost) PING min/avg/max = /0.01/ ms loss=0% 14:42:47 runPing, Finished with exit=1, nodedown=false 14:42:47 getNodeInfo, Starting 14:42:47 getNodeInfo, sysObjectId=1.3.6.1.4.1.8072.3.2.10, sysObjectName=_linux ... 14:42:47 Number of Data Points: 17, Sum of Bytes: 136, RRDs updated: 1, Nodes with Updates: 1 14:42:47 End of nmis-Config-update-localhost Processed 1 nodes ran for 1 seconds. |
As the installer has already installed the default NMIS cron schedule NMIS will poll and collect all known nodes every 5 minutes. You can now either run a test collect or sit back and wait for NMIS to do the next one automatically:
Code Block |
---|
sudo /usr/local/nmis8/bin/nmis.pl type=collect info=true |
After that collect operation has concluded you should see the newest data for your NMIS server on the NMIS dashboard.
Advanced Installer Use
If you want to read the installer source, or access the distributed files without actual installation, then simply pass the arguments –-keep --noexec
to the run file invocation, e.g.
Code Block |
---|
sh ./nmis8.5.10g.run --keep --noexec |
This tells the self-extracting installer to just unpack the archive (into the directory nmis<version>
) and to not start the interactive installer component.
If you want the installer to install NMIS into a non-standard directory, change to invocation to include site=<somepath<somepath>
(after a --
separator), e.g.
Code Block |
---|
sh ./nmis8.5.10g.run -- site=/opt/nmis |
If you don't want to perform the actual installation but only perform the software dependency resolution and check and install any prerequisites, use listdeps=true
(after a --
separator), e.g.
Code Block |
---|
sh ./nmis8.5.10g.run -- listdeps=true |
The installer creates a log of all the operations that it performs, which is saved in the main NMIS installation directory as install.log
. Subsequent NMIS upgrades add extra information to that log file, but the installer always starts its work with an initial log message that indicates when an installation/upgrade was performed.
Historical Manual Installation Instructions
The old manual installation instructions are available for your perusal on this page. Please note that these old instructions are no longer updated and will definitely diverge more or less from current best practice! (which is to let the installer handle the installation intricacies on your behalf).