NMIS supports using SNMPv3 for securing the collection of sensivite network information. This is especially important from core switches and routers which if compromised could have a considerable business impact. This configuration note does not include details about the SNMPv3 protocol, and assumes that people are wanting to use the authPriv (Authentication and Privilege) mode which is the most secure.
| Table of Contents |
|---|
IMPORTANT NOTE ON 256 BIT ENCRYPTION PROTOCOL SUPPORT
Regarding SNMPv3 protocol support, different vendors and even different products support different combinations of authentication and privilege protocols. The above example is for an older Cisco router, newer devices support SHA256 and AES256, the combinations will depend on your device.
Configuring Cisco IOS for SNMPv3
The first step is to enable SNMPv3 on your router or switch. If using Cisco IOS, the commands are below, if using other Cisco operating systems or other vendors, the concepts are the same and the commands will likely be similar. The most important thing is that the device will support SNMPv3, it will require encryption features if you want to use full auth/priv mode.
Required Cisco IOS Configuration for SNMPv3 communication to NMIS
The following three lines of Cisco IOS commands are required to enable SNMPv3 on the Cisco IOS device. When running a show run, the configured user will not show up in the running configuration, the configured users can be viewed by running the command "show snmp user".
| Code Block | ||
|---|---|---|
| ||
snmp-server view NMIS8RO iso included
snmp-server group NMIS8 v3 priv match exact read NMIS8RO
snmp-server user nmis8 NMIS8 v3 auth md5 nmis4242 priv des nmis4242
|
The commands above will create a user called nmis8, with an authorisation password of nmis4242 and a privilege password of nmis4242
View the configured SNMP users
| Code Block | ||
|---|---|---|
| ||
asgard# show snmp user
User name: nmis8
Engine ID: 800000090300001E13B18D00
storage-type: nonvolatile active
Authentication Protocol: MD5
Privacy Protocol: DES
Group-name: NMIS8 |
Details about Cisco IOS SNMPv3
More details about Cisco IOS SNMPv3 can be found at http://www.cisco.com/en/US/docs/ios/12_0t/12_0t3/feature/guide/Snmp3.html
Configuring Linux SNMP Daemon (Net-SNMP SNMPD) for SNMPv3
The first step is to enable SNMPv3 on in the /etc/snmp/snmpd.conf file, then restart the daemon.
Required Linux SNMPD Configuration for SNMPv3 communication to NMIS8
Add the following configuration to the top, edit the /etc/snmp/snmpd.conf file as the root user, e.g.
| Code Block |
|---|
sudo vi /etc/snmp/snmpd.conf |
Add the following configuration replacing the username and passwords is you require.
| Code Block | ||
|---|---|---|
| ||
createUser nmis SHA banana4242 AES monkey4242
rouser nmis priv 1.3.6.1 |
The commands above will create a user called nmis, with an authorisation password of banana4242 and a privilege password of monkey4242
The view of 1.3.6.1, will permit access to the Standard MIB and the Enterprise MIB, essentially providing full access.
Restart the SNMP Daemon
| Code Block | ||
|---|---|---|
| ||
sudo service snmpd restart |
Testing your SNMPv3 Configuration with NET-SNMP
To verify that SNMPv3 is working as configured run the following command. Change the username and passwords if you have used different ones.
| Code Block | ||
|---|---|---|
| ||
snmpwalk -v 3 -l authPriv -u nmis -a sha -A banana4242 -x aes -X monkey4242 <HOSTNAME> .1.3.6.1.2.1.1 |
Configuring NMIS9 for SNMPv3
Prerequisites
To use SNMP version 3 NMIS requires two perl modules that are not normally or automatically installed, Crypt::DES and Digest::HMAC.
From version 8.5.14 onwards the installer will try to install these modules; until then you'll have to resolve this dependency by hand:
- on Debian or Ubuntu use:
sudo apt-get install libcrypt-des-perl libdigest-hmac-perl - on RedHat/CentOS use:
sudo yum install perl-Digest-HMAC perl-Crypt-DES - or, if neither option appeals you may also use CPAN:
sudo cpan Crypt::DES Digest::HMAC.
Change Nodes.nmis Configuration
You can edit a Node using the NMIS GUI to include support for SNMPv3, as described in Adding and Editing a Device in NMIS8 (same works in NMIS9).
For NMIS 9 it can be done using the GUI or the node admin tool.
You will need to modify the node configuration to use SNMPv3, the user name, protocols and passwords need to match the above IOS or Linux configuration.
| Code Block | ||
|---|---|---|
| ||
/usr/local/nmis9/admin/node_admin.pl act=set node=<YOURNODENAME> \
entry.configuration.authpassword=banana4242 \
entry.configuration.authprotocol=sha \
entry.configuration.privpassword=monkey4242 \
entry.configuration.privprotocol=aes \
entry.configuration.username=nmis \
entry.configuration.version=snmpv3 |
Test NMIS SNMPv3 communication to the device
Ensure NMIS has the necessary encryption modules installed, it may be missing Crypt::DES, you will only need to do this if you see an error message below
| Code Block | ||
|---|---|---|
| ||
cpan
install Crypt::DES |
Run a test NMIS collect to the device using SNMPv3
| Code Block | ||
|---|---|---|
| ||
/usr/local/nmis8/bin/nmis.pl type=collect node=asgard debug=true |
For nmis9, it can be done:
| Code Block | ||
|---|---|---|
| ||
/usr/local/nmis9/bin/nmis-cli type=schedule job.type=collect job.node=asgard job.verbosity=7 |
In nmis9, the credentials can be also tested with an admin tool:
| Code Block |
|---|
/usr/local/nmis9/bin/admin/test.pl act=snmp node=NODENAME |
An example output:
| Code Block |
|---|
*** Testing snmp with snmpget snmpv2c
Running... snmpget -v 2c -c **** host.opmantek.net 1.3.6.1.2.1.1.1.0
Result: iso.3.6.1.2.1.1.1.0 = STRING: "Cisco IOS Software, 1841 Software (C1841-ADVENTERPRISEK9-M), Version 12.4(25f), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 16-Aug-11 06:21 by prod_rel_team"
*** Testing snmp with internal NMIS API
SNMP session open to HOST success
Result: Cisco IOS Software, 1841 Software (C1841-ADVENTERPRISEK9-M), Version 12.4(25f), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 16-Aug-11 06:21 by prod_rel_team
** Model: CiscoRouter
|
In the command output you are looking to verify that data was collected from the device, so any updates to an RRD will show that data was collected and is being stored.
| Code Block | ||
|---|---|---|
| ||
--snip--
11:19:02 updateRRD, DS MemoryUsedPROC:MemoryFreePROC:avgBusy5:avgBusy1:bufferFail:bufferElHit:MemoryFreeIO:bufferElFree:MemoryUsedIO
11:19:02 updateRRD, value N:19299276:27249732:3:2:0:810903:30345952:1118:4257056
--snip-- |
You should now be using SNMPv3 to communicate with this device from NMIS8.
Related Topics
NMIS supports using SNMPv3 for securing the collection of sensivite network information. This is especially important from core switches and routers which if compromised could have a considerable business impact. This configuration note does not include details about the SNMPv3 protocol, and assumes that people are wanting to use the authPriv (Authentication and Privilege) mode which is the most secure.
| Table of Contents |
|---|
Configuring Cisco IOS for SNMPv3
The first step is to enable SNMPv3 on your router or switch. If using Cisco IOS, the commands are below, if using other Cisco operating systems or other vendors, the concepts are the same and the commands will likely be similar. The most important thing is that the device will support SNMPv3, it will require encryption features if you want to use full auth/priv mode.
...
The commands above will create a user called nmis8, with an authorisation password of nmis4242 and a privilege password of nmis4242
View the configured SNMP users
| Code Block | ||
|---|---|---|
| ||
asgard# show snmp user User name: nmis8 Engine ID: 800000090300001E13B18D00 storage-type: nonvolatile active Authentication Protocol: MD5 Privacy Protocol: DES Group-name: NMIS8 |
Configuring Linux SNMP Daemon (Net-SNMP SNMPD) for SNMPv3
The first step is to enable SNMPv3 on in the /etc/snmp/snmpd.conf file, then restart the daemon.
Required Linux SNMPD Configuration for SNMPv3 communication to NMIS8
Add the following configuration to the top, edit the /etc/snmp/snmpd.conf file as the root user, e.g.
...
The view of 1.3.6.1, will permit access to the Standard MIB and the Enterprise MIB, essentially providing full access.
Restart the SNMP Daemon
| Code Block | ||
|---|---|---|
| ||
sudo service snmpd restart |
Testing your SNMPv3 Configuration with NET-SNMP
To verify that SNMPv3 is working as configured run the following command. Change the username and passwords if you have used different ones.
...
Configuring NMIS8 for SNMPv3
Prerequisites
To use SNMP version 3 NMIS requires two perl modules that are not normally or automatically installed, Crypt::DES and Digest::HMAC.
From version 8.5.14 onwards the installer will try to install these modules; until then you'll have to resolve this dependency by hand:
- on Debian or Ubuntu use:
sudo apt-get install libcrypt-des-perl libdigest-hmac-perl - on RedHat/CentOS use:
sudo yum install perl-Digest-HMAC perl-Crypt-DES - or, if neither option appeals you may also use CPAN:
sudo cpan Crypt::DES Digest::HMAC.
Change Nodes.nmis Configuration
You can edit a Node using the NMIS GUI to include support for SNMPv3, as described in Adding and Editing a Device in NMIS8, you can also edit the Nodes.nmis file to set the details.
...
You should now be using SNMPv3 to communicate with this device from NMIS8.
Details about Cisco IOS SNMPv3
More details about Cisco IOS SNMPv3 can be found at http://www.cisco.com/en/US/docs/ios/12_0t/12_0t3/feature/guide/Snmp3.html