Skip to end of banner
Go to start of banner

opEvents Installation Guide

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 11 Next »

Prerequisites

  • The individual performing this installation has a small bit of Linux experience.

  • Root access is available.

  • Internet access is required for installing any missing, but required software packages.
  • NMIS must be installed on the same server that opEvents is being installed on. If you do not yet have a working installation of NMIS in your server, please follow the procedure in the NMIS 8 Installation Guide and install NMIS before installing opEvents
  • You will need a license for opEvents (evaluation available HERE).

Preparation

  • For detailed information about Opmantek's interactive installer, including installation options (non-standard directory, non-interactive install, etc.)  please review the Opmantek Installer page.

  • opEvents requires a working MongoDB installation (but not necessarily on the same server). With opEvents 1.2.6 and newer the installer will install and configure MongoDB for you. For previous versions of opEvents please follow the instructions in the MongoDB Installation Guide

    • While opEvents does not require any specific MongoDB setup, you will have to provide opEvents with the correct MongoDB server information, database name and user name/password (if you use authentication). opEvents works best with the default database name "nmis", and with MongoDB authentication enabled.

  • Download opEvents from the Opmantek website.

Installing (or Upgrading) opEvents

Transfer the opEvents installer onto the server in question, either by direct download from the Opmantek website (using wget as demonstrated below), or from your desktop with scp, sftp or a similar file transfer tool.
Make a record of where you put the installer (we recommend using root's home directory or /tmp as good locations).

  • Remember, you must have root access to run the installer, so either use sudo or log in as root:

    # become root
sudo sh
# If using wget, for example, change into the directory you want to download the installer into 
cd /tmp
# Here's an example of using wget to retrieve the installer from Opmantek's S3 server:
wget http://dl-omk.opmantek.com/opEvents-Linux-x86_64-2.4.1.run

  • Start the interactive installer and follow its instructions. The installer now fully covers both initial installations as well as upgrades from earlier versions of opEvents.

    # Next, start the interactive installer and follow the prompts.
sh ./opEvents-Linux-x86_64-2.4.1.run

++++++++++++++++++++++++++++++++++++++++++++++++++++++
opEvents (2.4.1) Installation script
++++++++++++++++++++++++++++++++++++++++++++++++++++++

This installer will install opEvents into /usr/local/omk.
To select a different installation location please rerun the 
installer with the -t option.
...
  • The installer will interactively guide you through the steps of installing opEvents. Please make sure to read the on-screen prompts carefully.
  • When the installer finishes, opEvents is installed into /usr/local/omk, and the default configuration files are in /usr/local/omk/conf, ready for your initial config adjustments.
  • A detailed log of the installation process is saved as /usr/local/omk/install.log, and subsequent upgrades or installations of other Opmantek products will add to that logfile.

For opEvents 1.2.3 Only

The installer for opEvents 1.2.3 may warn about two "incorrect checksum detected" for two files, if you install this version on top of the Opmantek Virtual Appliance version 8.5.6G, or after other Opmantek applications that were released since opEvents 1.2.3. These warnings are benign and you can safely confirm that the installer is allowed to 'overwrite' those files.

 

Initial Configuration

  • You will need to adjust the MongoDB-related settings:
    open conf/opCommon.nmis in an editor, go to the database section and change the server, username and password to reflect your MongoDB installation.
    The result should look similar to the following (but there might be extra settings related to other products):

    'database' => { 
	'db_server' => 'localhost', 
	'db_port' => '27017',
	'db_name' => 'nmis',
	'db_username' => 'opUserRW',
	'db_password' => 'op42flow42',
},

 

  • For opEvents versions before 1.2.2 Only 
 Click here to expand...

you'll need to initialize your MongoDB with suitable indices. opEvents version 1.2.2 and later take care of that step for you automatically.

To perform this operation, run the following command as root:

/usr/local/omk/bin/opeventsd.pl act=setup
# you can also get an overview of opeventsd's capabilities by running opeventsd.pl --help

 

  • After completing your configuration changes you'll need to restart both the opEvents daemon as well as the Opmantek daemon.
    Simply run the following commands as root:

    # don't forget to become root, using sudo sh or su
service opeventsd restart
service omkd restart
# to verify the status of the daemons:
service opeventsd status
service omkd status

Where to go from here

First you should test opEvents: open up a web browser, and point it to "http://<yourserverip>/omk/opEvents"; you will have to enter your license first, then you will see opEvents' main dashboard.

opEvents offers a rich and flexible set of configuration options to ensure it meets your requirements, but there are many more options than can be listed here. Please consult the opEvents documentation for details.

 

  • No labels