Skip to end of banner
Go to start of banner

Using SNMPv3 with NMIS for Secure Network Management

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 9 Next »

NMIS supports using SNMPv3 for securing the collection of sensivite network information.  This is especially important from core switches and routers which if compromised could have a considerable business impact.  This configuration note does not include details about the SNMPv3 protocol, and assumes that people are wanting to use the authPriv (Authentication and Privilege) mode which is the most secure.

Configuring Cisco IOS for SNMPv3

The first step is to enable SNMPv3 on your router or switch.  If using Cisco IOS, the commands are below, if using other Cisco operating systems or other vendors, the concepts are the same and the commands will likely be similar.  The most important thing is that the device will support SNMPv3, it will require encryption features if you want to use full auth/priv mode.

Required Cisco IOS Configuration for SNMPv3 communication to NMIS8

The following three lines of Cisco IOS commands are required to enable SNMPv3 on the Cisco IOS device.  When running a show run, the configured user will not show up in the running configuration, the configured users can be viewed by running the command "show snmp user".

snmp-server view NMIS8RO iso included
snmp-server group NMIS8 v3 priv match exact read NMIS8RO 
snmp-server user nmis8 NMIS8 v3 auth md5 nmis4242 priv des nmis4242

The commands above will create a user called nmis8, with an authorisation password of nmis4242 and a privilege password of nmis4242

View the configured SNMP users

asgard# show snmp user 
User name: nmis8
Engine ID: 800000090300001E13B18D00
storage-type: nonvolatile active
Authentication Protocol: MD5
Privacy Protocol: DES
Group-name: NMIS8

Configuring Linux SNMP Daemon (Net-SNMP SNMPD) for SNMPv3

The first step is to enable SNMPv3 on in the /etc/snmp/snmpd.conf file, then restart the daemon.

Required Linux SNMPD Configuration for SNMPv3 communication to NMIS8

Add the following configuration to the top, edit the /etc/snmp/snmpd.conf file as the root user, e.g.

sudo vi /etc/snmp/snmpd.conf

Add the following configuration replacing the username and passwords is you require.

createUser nmis8 MD5 nmis4242 DES nmis4242
rouser nmis8 priv 1.3.6.1

The commands above will create a user called nmis8, with an authorisation password of nmis4242 and a privilege password of nmis4242

The view of 1.3.6.1, will permit access to the Standard MIB and the Enterprise MIB, essentially providing full access.

Restart the SNMP Daemon

sudo service snmpd restart

Testing your SNMPv3 Configuration with NET-SNMP

To verify that SNMPv3 is working as configured run the following command.  Change the username and passwords if you have used different ones.

snmpwalk -v 3 -l authPriv -u nmis8 -a md5 -A nmis4242 -x DES -X nmis4242 <HOSTNAME> .1.3.6.1.2.1.1

Configuring NMIS8 for SNMPv3

Prerequisites

To use SNMP version 3 NMIS requires two perl modules that are not normally or automatically installed, Crypt::DES and Digest::HMAC.
From version 8.5.14 onwards the installer will try to install these modules; until then you'll have to resolve this dependency by hand:

  • on Debian or Ubuntu use: sudo apt-get install libcrypt-des-perl libdigest-hmac-perl
  • on RedHat/CentOS use: sudo yum install perl-Digest-HMAC perl-Crypt-DES
  • or, if neither option appeals you may also use CPAN: sudo  cpan Crypt::DES Digest::HMAC.

Change Nodes.nmis Configuration

You can edit a Node using the NMIS GUI to include support for SNMPv3, as described in Adding and Editing a Device in NMIS8, you can also edit the Nodes.nmis file to set the details.

You will need to modify the NMIS8 configuration to use SNMPv3, the user name, protocols and passwords need to match the above IOS configuration.

 'version' => 'snmpv3',
 'authkey' => '',
 'username' => 'nmis8',
 'authpassword' => 'nmis4242',
 'authprotocol' => 'md5',
 'privpassword' => 'nmis4242',
 'privprotocol' => 'des',

For NMIS 9 it can be done using the GUI or the node admin tool. 

Test NMIS8 SNMPv3 communication to the device

Ensure NMIS has the necessary encryption modules installed, it may be missing Crypt::DES, you will only need to do this if you see an error message below

cpan
install Crypt::DES

Run a test NMIS collect to the device using SNMPv3

/usr/local/nmis8/bin/nmis.pl type=collect node=asgard debug=true

For nmis9, it can be done: 

/usr/local/nmis9/bin/nmis-cli type=schedule job.type=collect job.node=asgard job.verbosity=7

In nmis9, the credentials can be also tested with an admin tool:

/usr/local/nmis9/bin/admin/testsnmp.pl node=NODENAME

An example output:

*** Testing snmp with snmpget snmpv2c
 Running...     snmpget -v 2c -c **** host.opmantek.net 1.3.6.1.2.1.1.1.0 
 Result: iso.3.6.1.2.1.1.1.0 = STRING: "Cisco IOS Software, 1841 Software (C1841-ADVENTERPRISEK9-M), Version 12.4(25f), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 16-Aug-11 06:21 by prod_rel_team"



*** Testing snmp with internal NMIS API 
 SNMP session open to HOST success 

    Result: Cisco IOS Software, 1841 Software (C1841-ADVENTERPRISEK9-M), Version 12.4(25f), RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 16-Aug-11 06:21 by prod_rel_team

** Model: CiscoRouter


In the command output you are looking to verify that data was collected from the device, so any updates to an RRD will show that data was collected and is being stored.

--snip--
11:19:02 updateRRD, DS MemoryUsedPROC:MemoryFreePROC:avgBusy5:avgBusy1:bufferFail:bufferElHit:MemoryFreeIO:bufferElFree:MemoryUsedIO
11:19:02 updateRRD, value N:19299276:27249732:3:2:0:810903:30345952:1118:4257056
--snip--

You should now be using SNMPv3 to communicate with this device from NMIS8.

Details about Cisco IOS SNMPv3

More details about Cisco IOS SNMPv3 can be found at http://www.cisco.com/en/US/docs/ios/12_0t/12_0t3/feature/guide/Snmp3.html

  • No labels