Skip to end of banner
Go to start of banner

Event Correlation

Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 10 Next »

opEvents does not just automatically suppress duplicate events (stateful or custom-matched); it can also create new events based on correlating recent event occurrences.
In versions 2.0.4 and newer you can use fine-grained controls to deal with the triggering events, and from version 2.2 onwards the contents of synthetic events are configurable, too.

This  page describes how to configure event correlation.

 

General Configuration

This event correlation and synthesis feature is configured in the same way as the duplicate suppression, namely by putting event creation rules into conf/EventRules.nmis.

An event synthesis rule consists of:

  • an event name, which specifies the name of the newly created event,
  • a list of events (more precisely, their names), which are the events to consider for correlation,
  • a (minimum) count of events that have to be detected to trigger the rule,
  • an optional list of groupby clauses, which define whether the count is interpreted globally for all named events, or separately within smaller groups,
  • optional delayedaction and autoacknowledge clauses, which define how the triggering events should be handled,
  • an optional enrich clause, which adjusts the content of the newly created event,
  • from version 2.2.0a onwards, optional copy_firstcopy_lastcopy_highest and copy_groupby clauses which further control the contents of the newly created event,
  • from version 2.2 onwards, an optional inhibit parameter, which disables correlation temporarily after a rule has fired,
  • and finally a window parameter, which defines the time window to examine.

(If you compare suppression and synthesis rules closely, you'll see that the main difference is the lack of a suppress clause for synthesis rules, whereas the suppression rules don't  have enrich or copy_* clauses.)

Here is an example rule:

'3' => {
	name => 'Customer Outage',
 	events => ["Node Down","SNMP Down"],
 	window => '60',
 	count=> 5,
 	groupby=>['node.customer'], # count separately for every observed value of customer
 	enrich=>{priority => 3, answer => 42}, # any such items gets inserted in the new event
},

This rule causes opEvents to look for Node Down and SNMP Down events in the last 60 seconds, separate them into per-customer groups (see grouping below); if it counts 5 or more such events in a group, then a new event called Customer Outage is created.

Grouping

If no groupby clause is present, then potential trigger events are selected solely by event name and event time (within the window), without any further scope limiting, i.e. globally across all nodes. For many common scenarios this may be too broad a selection; for example creating new events for a particular customer or service group only wouldn't be possible.

Grouping solves this problem: the set of potential triggering events is split into groups with matching property values and the count threshold is applied to those groups.

The groupby clause has the form of a list of node.X or event.Y property specifications (e.g. node.customer or node.group), which are used to group events into buckets for counting: only events that share the same values for all the listed grouping properties will be counted together.

For example, the groupby clause [ 'node.customer', 'event.priority' ] would cause this correlation rule to be applied independently for all combinations of customer and event priority. The clause given in the example block above will create a Customer Outage event for any individual customer with 5 outages in 60 seconds; without the groupby any 5 outages anywhere would cause a synthetic event to be created.

The groupby clause can make use of all common node properties which are listed here and  the standard event properties which are documented on this page. Please note, however, that only event properties that were set during the event parsing stage are accessible when correlation is performed. For example policy actions can change an event (e.g. tagging, script execution) but policy actions are performed after correlation.

Event Content and Enrichment

Before opEvents version 2.2, synthetic events are always cloned from the most recent triggering event, then they get a new name from the synthesis rule name, and finally any static enrich clauses are evaluated. Synthetic events could not be stateful events, i.e. they were not subject to deduplication and could not be acknowledged (or 'closed') by any later 'opposite' event.

In version 2.2 this limitation has been removed, and much more precise control of the event content is possible.

Content Control Directives (Version 2.2.0a and newer)

When a synthesis rule creates a new event, the following steps are performed:

  1. If no copy_firstcopy_lastcopy_highest or copy_groupby directives are present, then a backwards-compatible directive 'copy_last => [ qr// ]' is added.
  2. copy_first is evaluated first, and specifies which event properties should be copied over from the earliest trigger event.
    Each listed property is copied over; if the directive contains a regular expression (e.g. qr/cust.*/, then all properties with names matching the regular expression are copied.
  3. copy_last is checked next, and properties listed here are copied over from the most recent trigger event.
    The property copying does overwrite all properties that were set earlier (by copy_first).
  4. copy_highest is checked next, and its properties are sourced from the trigger event with the highest priority.
    Again overwriting of properties may happen.
  5. copy_groupby controls whether any of the grouping property values should be saved in the new event.
    The format is different for this directive: It must be a list of property target names (or the word 'undef'), in the same order as the groupby directive.
    For each element  in the groupby list, the value of the grouping property is saved as the target name in the new event, if a target name is available in the copy_groupby list.
    If no groupby is given for this rule, then a copy_groupby directive has no effect.
  6. Now the enrich clause is checked, and each of  its property name - value pairs indicates which properties should be set to (or overwritten with) a particular static value.
  7. Now  the  nodestateful and element properties are automatically adjusted if required (see below for details).
  8. Finally, the event name is set to the rule name, certain undesirable properties are removed, an audit trail of triggering events is added (by adding the properties nodes and eventids), the event is marked as synthetic and is inserted into the database.

Automatic Event Node for Synthetic Events

If no copy_* or enrich clause has caused the the node property to be set explicitly, then the global default node is used instead.

'Set explicitly' means a copy_* or enrich clause did include the node property, i.e. not if the node property copying happened because of a regular expression.

The global default node in opEvents 2.2 is configurable using the configuration item opevents_correlation_node, and it's normally called "global".
This virtual node is automatically (re)created if missing.

This behaviour is different from opEvents before 2.2, where all synthetic events were attached to the last trigger event's node. To emulate the old behaviour you have to change your correlation rules, so that they include the directive

copy_last => [qr//, 'node']

which causes a blanket copy of all properties from the last trigger event and an explicit copy of the node property (to disable the automatic event node choice).

Example Rule

Here is an example rule demonstrating the new directives:

'1' => {
   name => "Very Sick Node",
   events => [ "Node Down", "SNMP Down", "Interface Down", "Service Down",
               "Service Degraded", "Interface Flap", "Node Flap", "WMI Down" ],
   window => 120,
   count => 3,
   groupby => [ 'node.name' ], # we want separate events for each node of course
   enrich => { stateful => "Very Sick Node", priority => 5, state => 'down', element => undef }, # new event is stateful only if stateful is set or copied by name
   copy_last => [ qr//, 'node' ], # can set from node here (all events share it)
   copy_groupby => [ 'node' ], # or from here; must set it explicitely somewhere, or the event goes to opevents_correlation_node
},

Stateful Synthetic Events (Version 2.2.0a and newer)

By default, synthetic events are not stateful events, i.e. they are not subject to deduplication and they cannot be acknowledged (or 'closed') by any future 'opposite' event.

However, in 2.2 and newer it is possible to enable stateful handling for synthetic events:

  1. Your rule must explicitly set the stateful property.
    Copying with a regular expression in copy_* does not meet this requirement, and a thusly copied stateful property is deleted before event creation.
  2. Your rule must ensure that a suitable state property value is present.
  3. Your rule should ensure that a suitable  element property value is present, or opEvents will automatically create one from groupby information if that is available.
    As described in the documentation for Stateful Events, the combination of node, stateful  and element properties must uniquely identify the stateful 'thing', and the value of the state property describes the new state.

The example rule above shows how a stateful 'very sick node' event can be created: the node name is set from the grouping criteria (i.e. all related triggers share the same node name), the stateful property is set with a static enrich clause, and there is no  element, so at most one 'very sick node' stateful thing can exist for a single node.

If we wanted to acknowledge this event from a different correlation rule, we'd have to ensure that node, stateful and element properties with the same  value are generated, but the state would have to be 'up' or 'closed' or 'ok'.

Here is another example, for a group-level stateful event:

8 => {
    name=>'sick group',
    events=>["Service Down","SNMP Down", "Node Down"],
    groupby => [ 'node.group' ],
    window=>150,
    count=>3,
    enrich => { stateful => "sick group", state => "down" },  # node will be opevents_correlation_node, element will be group
    copy_last => [ qr// ],
},
9 => {
    name=>'happy group',
    events=>["Service Up", "some nice event" ],
    groupby => [ 'node.group' ],
    window=>300,
    count=>1,
    enrich => { stateful => "sick group", state => "up" },
    copy_last => [ qr// ],
},

Rule 8 specifies that three of the listed 'down' events in a single group should cause a new event that sets the 'sick group' state to down for this one group; the element property is auto-generated from the groupby data,  and all such events are attached to the virtual node 'global'. Any repeat 'sick group' events would be statefully deduplicated. Because element is  set to the group in question, every single group would have its own 'sick group' state.

As soon as a single positive event from the list in rule 9 arrives, the 'sick group' event is acknowledged and closed.

Event Processing for Synthetic Events

At this point the new event is inserted into the database, and is ready for further action processing. This action processing (e.g. escalation, mail notification, custom logging) is performed immediately.

Handling of the Triggering Events

Please note that this feature is only available in opEvents 2.0.4 and newer.

  • If your rule contains a delayedaction clause (with a numeric value), then all potentially triggering events will have their action processing delayed by the given number of seconds.
    This affects all events whose name is in the event list of your rule, no matter whether the limits for triggering a synthetic event have been met or not. The delayaction value should therefore be set to a relatively small value.
  • If your rule has the property autoacknowledge set to true or 1, then all triggering events will be automatically acknowledged and all action processing for them will be aborted.

The combination of these two controlling properties provides fine-grained storm control and the ability to create "combination events" that subsume and close any number of triggering events:

"Plain" Synthetic Events

If your rule sets neither delayedaction nor autoacknowledge, then the incoming potential trigger events will be processed as per normal and immediately, and any policy actions for them will be taken as soon as possible (but possible after being delayed by the state_flap_window - see Deduplication and storm control in opEvents for details). The trigger events are thus completed, and visible as current/unacknowledged, completely independent of any synthetic events that might get triggered by them later.

"Combination" Events

If your rule sets delayedaction (and optionally autoacknowledge), then the incoming events are delayed and held for the given time before any policy actions are taken for them. (The delayedaction setting should be the same as or larger  than the rule's window setting.)

If the requirements for a synthetic event are met during that time, then the new synthetic event can "combine" and supersede the triggering events. If autoacknowledge is set, then all the triggering events will be acknowledged, closed and no actions will be taken for them at all. (Without autoacknowledge the triggering events would not have actions performed but would  remain unacknowledged.)

The net effect is that the current events view would show only the new synthetic event as 'current' and all the underlying triggering events would be categorized as closed (and optionally acknowledged), and thus be mostly hidden.

Synthetic Events and Storm Control

All synthesis rules are applied independently, thus a single event could be a trigger for multiple synthetic events. This is desirable for example for detecting both per-customer problems and global issues at the same time: a few problem events can trigger a customer-specific action, while the same events could be counted together with others for detecting and reacting to a major outage.

Great care has been taken to avoid event storms caused by synthetic events: When a synthesis rule fires because there were more than count matching events in the time window, then all the matching events are marked as consumed and will not be considered for any future synthesis for this rule. In other words, there is no overlap between successful synthesis time windows. If a rule does not trigger because there are fewer than count trigger events, then naturally these events remain potential triggers until the time window moves past them.

However, synthetic event creation currently happens immediately as soon as a sufficient number of triggers are detected: assuming a trigger of a minimum 20 events in 60 seconds, receiving 100 events in that time frame will cause a new synthetic event for each of the 20 sufficient triggers.

Inhibiting Correlation (Version 2.2 and newer)

Version 2.2 provides a new capability for fine-tuning storm control: the inhibit timer.

If a correlation rule fires, and if that rule contains a numeric inhibit parameter greater than zero, then opEvents will temporarily disable the  rule with its particular groupby context for that many seconds.

The primary application of this feature is to stop 'nuisance' repeat synthetics if a very large number of triggers arrives in a very short time frame: it lets you tell opEvents to generate at most one instance of a particular event every inhibit seconds.

Here is an example scenario: let's assume a rule for raising a 'Group Outage' event if 20 instances of a particular event are seen within a window of 60 seconds. A major outage happens, and 100 such trigger events for group A arrive within just a seconds, and a further 25 triggers for group B.

  1. Without inhibit, after the first 20 events for group A you'll get one synthetic event for group A; another after the next 20 and so on.
    For group B, one synthetic event will be generated for the first 20; the remaining 5 are too few to trigger anything.
  2. With inhibit set to 40 seconds (for example), you'll get the very first group A synthetic event as before, but then no synthetic events for this rule and group A for the next 40s;
    After that correlation for group A resumes 'from scratch' and any events received from then onwards are counted and correlated as normal.
    For group B with its fewer triggers the inhibit behaviour doesn't change anything visibly, there's still just one synthetic event.
    Note that the inhibit timer for group A is totally independent of any inhibit for group B: inhibit applies to a particular rule and its full groupby context.

 

  • No labels